Telephone socket installation

You can also use two cleats as shown to hold a cable bend neatly in place, not a single cleat on the bend. Next cut away the unwanted sheath with the side cutters. Do not remove the PVC insulation from the wires themselves. Fix the cable sheath s neatly to the cable mount on the faceplate of the socket using the nylon tie provided with the socket. Put the cable in place and tighten the tie see diagram below. Cable securing methods may differ depending on the make of the socket.

Spread out the individual wires so that you can identify the colours. In each socket the wiring HAS to be connected as follows Incorrect wiring may cause faulty operation or damage to the system. Terminating the wires No wire stripping or soldering is necessary to make a good termination. Always wear eye shields when using IDC tools as the wire ends can fly off.

This is essential, as not only will the tool be damaged but also the wire will not be terminated properly if the tool is incorrectly used. It is recommended that you practice first by placing the IDC tool over a terminal, without a wire in place.

In the correct position the tool will easily slide as far as the chamfer of the plastic insulator on the terminal. Leaving a small amount of slack in the wire place the wire to be terminated in the appropriate slot of the terminal.

Put the tool into position. A firm vertically applied pressure to the tool will force the wire into the connector fork and the connection is made. You will hear it go into place. Then remove any excess wire beyond the connector with the wire side cutters. The picture shows the cheap wiring tool, if the Krone version is used, then the scissors side locates in the recessed side shown to the right in the picture.

The Krone tool also automatically cuts off the spare wire. If two cables are to be connected to the socket, a second wire will need to be inserted at the same terminal. Each wire must be inserted individually and not both at once. Plug your telephone or DSL cable into your newly installed jack. Your phone should have a dial tone, and your internet connection should work now as long as your computer is correctly set up for a DSL connection. If the phone line does not seem to be working, you may need to unscrew the new jack and make sure the wires are connected to the proper places and correctly screwed in.

If further electrical work is required, make sure to go back to the NID and disconnect the phone line again before manipulating the wires. Daniel Stoescu Master Electrician. Daniel Stoescu. Place the wires onto the designated terminals on the mounting plate.

The red and green wires go with the primary line, while the black and yellow wires go with the secondary line. Not Helpful 0 Helpful 0. I have a cable connection and a phone jack in the same box. The cable works, but the phone jack doesn't. How can i change it? It's easier to just buy a new piece, if you want the connections to be in the same housing. Not Helpful 10 Helpful Bring in the owner of the company you bought the phone from; you're going to need to know what the wires mean now, and use Washi tape or similar to colour code them.

Whilst doing that, write down which colour means what. That way, every time you need to use the cables and wires just look at your sheet. Not Helpful 19 Helpful The white and orange wires are now obsolete. New wires and plugs have gray and purple.

If those colors are not available, replace the wiring. Not Helpful 21 Helpful Connect with the two screws closest to the wire hole, or farthest from the phone jack side tip and ring. It does not matter which side each goes on. If you are installing a wall plate, it goes on the green and red terminals. Not Helpful 0 Helpful 1. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.

If you'd prefer not to run wires along your baseboards or walls, consider threading them through your walls, instead. Helpful 1 Not Helpful 6. A standard residential telephone line coming into your home has very little voltage. However, if your phone were to ring while you were working on a connected wire, the voltage would increase and could be dangerous.

Take the precaution of disconnecting your phone line before doing electrical work. Helpful 11 Not Helpful You Might Also Like How to. How to. Master Electrician. Expert Interview. Videos provided by Canadian Tire. About This Article. Co-authored by:. Co-authors: Updated: October 18, Categories: Telephones. Thanks to all authors for creating a page that has been read , times.

Is this article up to date? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Emily Webster Jul 22, Call Recording Automatically or on-demand record call conversations for quick lookup and verification purposes.

Enhance Customer support Directing calls, email, faxes, and chats off to the right person instantly using the advanced routing techniques. Telecom Products. Avaya Telephone System. Cisco Telephone System. Yeastar MyPBX. Polycom Products.

Yealink Voip Phones. Samsung Telephony. RTX Dect Phone. SNOM Phones. Check Our Related Services:. Office Telephone System. Telephone systems for Hotels. Home Telephone Systems. Telephone System Installation. Phone System Maintenance Contract.